8210 uTrust Touch Secure Keypad Reader

Search

Introduction


This document details the Physical Access Control Reader uTrust TS KEYPAD and its basic user instruction and installation procedures.

Reader

Functionality


TS KEYPAD reader is a physical access control smart card reader that can read HF and LF contactless credentials, conforming to the following standards: ISO 14443 A & B, ISO15693 with a keypad PIN entry for additional security. The reader can interface with an access control system equipped with a Wiegand or RS-485 serial interface. User interfaces include RGB LED’s and Buzzer.

Reader Parts


a. Front/Top Casing

b. Back View/Plate

c. Back Plate

Product Details


Model Name

uTrust TS keypad

Device Type

RFID reader, 13.56 MHz (HF) / 125 KHz (LF), keypad
Physical Access control Reader (accessory equipment)

Type of Equipment

Potted Reader, Suitable for Indoor use

Interface Type

Phoenix connectors

Voltage Rating

6 - 16VDC

Current Rating @ 12V

Peak Current - 157 mA, Average Current 110 mA

Communication Protocol

Wiegand, RS-485 (2wire - Half Duplex)

Specifications


Model

Operating Voltage

Current @ 12V

Operating Temp

Operating Humidity

Model

Operating Voltage

Current @ 12V

Operating Temp

Operating Humidity

8210
uTrust TS
KEYPAD

6 - 16VDC

Av -110 mA
Pk -157 mA

0 to +49C

85 +/-5 % RH

Label


During wiring, make sure that the +VDC lines does not make contact with any other cables, as it might affect reader functionality/cause damage to the reader.

Installation Details


Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction.

Parts List


  • TS Keypad reader - 1

  • Screws (A #6-18X1.5" SS ) - 4 No's - Back Plate mounting screws for wall

  • Snake Eye Screw (SMF #6-32X5/16" SS) - 1 No - Top casing mounting security screw

  • Screws (SMF #6-32x3/8" SS) - 3 No’s - 1 casing to back plate mounting screw and 2 junction box mounting screws

  • Nylon anchor plug - 4 No’s

  • 6 pin phoenix plug (Phoenix connector version only) - 2 No’s

  • Back Plate

Recommended Infrastructure


All cabling and wiring shall be UL Listed and/or UL Recognized.

Cable Wiegand

22 AWG Shielded cable. (Cable P No : ALPHA WIRE, P/N 1299/10C)

Cable RS-485

RS-485 for 1000m** (4000ft) 24 AWG STP

Class 2 Linear DC PS

6 - 16V, 1A min.

** Tested in lab conditions up to 115K baud

Connector Information

Pinout diagram


Table 1

-Shield Ground/Drain - Black color should be connected to the cable shield.

 

During wiring, make sure that the +VDC lines does not make contact with any other cables, as it might affect reader functionality/cause damage to the reader.

Mounting the Reader

Location of mounting holes on wall


Reader Installation Steps


a. Make holes on the wall as per the image above
b. Insert the nylon screw plugs into the wall
c. Connect the wires as per the Table 1
d. TouchSecure® reader with Bottom Casing is to be now secured onto the wall using the Screws (A #6-18X1.5" SS)
e. The top casing can be inserted onto the bottom casing
f. Secure the Top and bottom casing by the Snake Eye Screw (SMF #6-32X5/16" SS)

Power up and Testing


1 Turn power on
The LED blinks 3 times green with a long beep, then turns red.
2 Present a card
The LED blinks green, and a short beep is emitted.
3 Press Key
Buzzer tone & backlight LED blinks.

4 Wiegand / RS485
Communication to the Panel is done through Wiegand / RS-485 / OSDP.


This is the default reader behavior.

Certifications

FCC


This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation


This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna

  • Increase the separation between the equipment and receiver

  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

  • Consult the dealer or an experienced radio/TV technician for help


Information to user
Changes or modifications not expressly approved by Identiv could void the user's authority to operate the equipment.

IC


This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device

UL 294 and UL 1076


  • Communication via Wiegand and OSDP was evaluated by UL and serves as the interface between the reader and panel

  • When the reader is powered by a supply other than Identiv Mx series controller, the power supply should be a UL 294 and 1076 listed , class 2 supply

  • For UL 1076, the reader was assessed for the acknowledgment signal annunciation while interfacing to the Listed Identiv Mx series control unit via Wiegand and OSDP only

UL 294 Access Control Performance Levels


Destructive Attack

Level IV

Line Security

Level I

Endurance

Level I

Standby Power

Level I

Â