CMD 103: CHANGE SELECTED MATCH FUNCTIONS
Syntax:
START 103 * N * 1/0 * Address 1-8 [* Address 9-16] #
Variables:
N
1 Channel 1 Card Reader LED Reversed
2 Channel 2 Card Reader LED Reversed
3 Physical Tamper
4 Card Reader LED follows Local Relay
5 Card Reader ScramblePad Sharing
6 DTA Externally Powered, allow keypress to activate LCD Unit Backlight
7 DTA Backlight ON continually
8 DTA Display Threat Level
1/0
1 ON
0 OFF
Address 1 - 8
012345678
Address 9 - 16 (optional)
012345678
Description:
This command controls several functions of the MATCH Reader Interface Board (MRIB) or the card readers attached to the MRIB. The factory setup for the reader status LED is to be normally off and to momentarily turn on when a card is read. This command allows the status LED functions to be reversed.
The MRIB can detect when the bezel of its mounting base is removed and can report the bezel OFF as a physical tamper alarm on the system printer, on the tamper alarm relay, and on the host PC, if installed. The factory setup for physical tamper is OFF. This command enables tamper reporting to be changed to ON.
When you enable Card Reader ScramblePad Sharing, it allows a ScramblePad or reader to use both reader types in the same dual technology setup. Ordinarily, a ScramblePad is only allowed to recognize one reader type at a time; however, some companies must provide access for employees who possess either a mag stripe card or a prox card in addition to a code. This feature enables employees to enter their code then swipe either their prox or mag stripe card to gain access.
There are several new options added for the DTA (DIGI*TRAC Annunciator). These enable backlighting and display threat levels.
Example:
START 103 * 1 * 1 * 1 * 0 #
Changes Card Reader Address 1 LED on Channel 1 to ON
Default:
Channel 1 & 2 reader LED not reversed
Physical Tamper disabled
Related CMDs:
📄 CMD 88*12 – Print Match Setups and Status
📄 CMD 188*3 – Print Setup Changes for Keypad/MATCH
CMD 03 – Change Selected Keypad/Match Functions
CMD 104 – Enable CARD/CODE-Only At Dual Technology
CMD 403 – Change Selected Keypad / MATCH Functions From Host [v7.0 and later]
CMD 104: ENABLE CARD/CODE ONLY AT DUAL TECHNOLOGY READER DURING TIME ZONE
Syntax:
START 104 * NN * Address * Time Zone #
Variables:
NN
1 Reader On Channel 1
2 Reader On Channel 2
Description:
This command enables the use of a card only at a dual technology reader during the specified time zone. This is often used at a card-only entry during normal working hours and at a dual (card + code) entry after hours. This command enables use of Card Only on either the entry or exit (Channel 1 or Channel 2) readers, or both.
To disable the use of card-only mode and return the reader to dual at all times, reenter the command with time zone 0.
For a list of available ID formats and their behavior, refer to Table 3-7 on page 3-24.
Example:
START 104 * 1 * 1 * 1 #
Enable Card Only at the Entry Reader of Channel 1 During Time Zone 1
START 104 * 1 * 1 * 0 #
Enable Dual Always and Disable Card Only at any time on the entry reader of Channel 1
Default:
None. No Dual readers will read Card Only.
Related CMDs:
📄 CMD 88*12 – Print Match Setups and Status
📄 CMD 188*3 – Print Setup Changes for Keypad/MATCH
CMD 03 – Change Selected Keypad/Match Functions
Time Zone Setups
CMD 52, 54, 154 – Define Standard, Master, Grand Master Time Zones
Adding Users
CMD 312, 313, 315 – Add Users, IDF 4, 5, 7.
CMD 105: DISABLE DEVICE DURING TIME ZONE
Syntax:
START 105 * Device * Time Zone #
Variables:
Device
1 Printer
2 SNIB
Description:
This command allows the printer and/or SNIB to be disabled during the specified time zone. This reduces the quantity of printouts which occur during high activity periods, or during any time period that printed records are not required.
Disabling the printer prevents all transactions from being logged to the printer and to the controller's internal memory buffer.
The SNIB can be disabled during specified times to disable network communications to and from the specified controller. If the network is active when the SNIB is disabled, communications will remain active until the S*NET host PC logs off the network. Logging back on will not be allowed until the SNIB is enabled at the end of the specified Time Zone.
To re-enable any device, re-enter the command and specify Time Zone 0 for that device.
Example:
START 105 * 1 * 1 #
Disable Printer During Time Zone 1
START 105 * 1 * 0 #
Reenable Printer to Always Print
Default:
Printer Always Prints
SNIB Always Communicates
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Reporting and Printing Setup
CMD 05 – Reporting Modes
CMD 06 – Disable printing of grants on selected doors
CMD 106 – Disable Reporting During Time Zone
CMD 107, 90*2#/97*1 – Daily Report Printing On/Off
CMD 109 – Invalid Code/ID Reporting Mode
Time Zone Setups
CMD 52, 54, 56 – Define/Clear Standard, Master Time Zones
CMD 108 – Time Zone Control of Modem
CMD 106: DISABLE REPORTING DURING TIME ZONE
Syntax:
START 106 * Report Type * Time Zone #
Variables:
Report Type
1 Transaction Reporting
2 Event Reporting
3 Grant Reporting
Description:
This command disables all code & RQE transaction reports, granted and denied, from reaching the system printer, or the host PC, if the controller is networked. All events, internal and external, can also be disabled during the specified time zone. Grant only transactions can be disabled during the specified time zone. Any denied transactions continue to be reported.
Disabling these reports prevents them from being logged to the printer, buffer, and Host PC.
Example:
START 106 * 2 * 1 #
Disable printed events during Time Zone 1
Default:
None are disabled. All report.
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Reporting and Printing Setups
CMD 05 – Reporting Modes
CMD 06 – Disable printing of grants on selected doors
CMD 105 – Disable Device During Time Zone
CMD 107, 90 * 2 # / 97 * 1 # – Daily Report Printing On/Off
CMD 109 – Invalid Code/ID Reporting Mode
Time Zone Setups
CMD 52, 54, 56 – Define/Clear Standard, Master Time Zones
CMD 107: DAILY REPORT PRINTING
Syntax:
START 107 * NN #
Variables:
NN
0 - OFF
1 - ON
Description:
This Command disables the automatic Daily Report of System Status that occurs every night at midnight. It also disables the Sunday Midnight System Status and configuration Report.
In v6.6 and later, the daily maintenance report no longer reports the system setups and status. Get these using CMD 88*0.
Example:
START 107 * 1 #
Enable The Daily Midnight Report
Default:
Daily Report Printing OFF
Related CMDs:
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Reporting and Printing Setups
CMD 05 – Reporting Modes
CMD 90*2# / 97*1 – Disable Daily Report
CMD 106 – Disable Reporting During Time Zone
CMD 108: TIME ZONE CONTROL OF MODEM
Syntax:
START 108 * NN * Time Zone # (v6.6 and earlier)
START 108 * 1 * TZ1 * TZ2 * TZ3 * TZ4 # (v7)
The first command syntax applies to all versions. The second command syntax is only applicable to v7.0 and later.
Variables:
NN
1 Trigger Dialing Host
2 Postpone Dialing Host
3 Cancel Dialing Host
4 Disable Answering Host
Description:
This command is part of the Remote Site Management feature set. It enables time zone control of the modem at a remote site. The modem can be set to dial the host PC at the main site at the start time of a specified time zone. This selection can be used to automatically upload a remote site's buffered events and alarms on a daily or weekly scheduled basis. It can also be used to provide a level of “supervision,” or automatic check-in, ‘I'm OK’ message, between any remote site and the main site. The second selection can be used to delay any alarms or events from dialing the host until the end time of the selected time zone. The third selection will cancel any attempt to dial the host during the specified time zone and the fourth selection disables the controller from answering the host during the specified time zone.
In v6.6 the dialing modem stops attempting to contact the remote site after trying 255 times in succession. (A typical attempt takes 30-40 seconds; 255 tries takes 1 to 3 hours.) The modem will resume trying the next time something triggers its modem dialer logic, or the next day, whichever comes first; however, after 255 attempts it will stop again.
In v7.0 and later, you can specify up to four time zones as triggers for dialing the host.
Example:
START 108 * 1 * 5 #
Dial Host At Start Time Of Time Zone 5
START 108 * 4 * 1 #
Disable Answering Host During Time Zone 1
START 108 * 1 * 2 * 4 * 5 #
Dial Host At Start Time Of Time Zone 2, Time Zone 4, and Time Zone 5
Default:
None. No Time Zone control of modem.
Related CMDs:
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*24 – Print Remote Site Management Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Modem Setups
CMD 193 – Set Host Phone Number(s)
CMD 194 – Select Tone or Pulse Dialing
CMD 195 – Change Host Call-Back
Time Zone Setups
CMD 52, 54, 56 – Define/Clear Standard, Master Time Zones
CMD 105* 2 – Disable SNIB During Time Zone
CMD 109: INVALID CODE REPORTING MODE
Syntax:
START 109 * NN #
Variables:
NN
0 OFF
1 ON
2 OFF
Description:
This command is used to track & record the occurrences of invalid code usage at each ScramblePad or card reader on the controller. An invalid code is one that does not exist in the controller's database or memory. In some installations, system managers are concerned over attempts to guess valid codes or the unauthorized use of an unreported lost, stolen, or unidentified card by either authorized users or unauthorized users. This feature can track these attempts by recording each use of an invalid code, which may be immediately followed by the use of a valid code. When this feature is enabled the actual invalid code entered will be printed out.
The ability to record invalid codes can illustrate if an orderly sequence or a random sequence of codes is being used in an attempt to discover a valid code. Likewise, it may disclose infrequent honest errors by authorized users during the code entry process such as digit transpositions or incorrect digit sequences.
When invalid codes are turned ON, it will display both invalid ScramblePad and MATCH codes.
Invalid Code Reporting can be used to determine a card's 8-digit MATCH code at a dual technology reader. Simply present the unenrolled card, then enter 000# at the ScramblePad. When the combination of card + 000 is denied by the controller, the card's MATCH code is sent to the host.
In v6.6, at a dual technology reader with “Invalid Code Reporting” enabled, an invalid card and code combination will result in the controller sending the card code to the host. In v6.6, when presented with an unenrolled card, will wait for a code and then looks up the resulting dual code in the database, even when in “Card/Code Only Mode” (CMD 109). This means that invalid code reporting doesn't take effect until after the dual code is rejected. “Invalid Code Reporting” can still be used to determine a card's 8-digit MATCH code at a dual technology reader. Simply present the unenrolled card, then enter 000# at the ScramblePad. When the combination of card + 000 is denied by the controller, the card's MATCH code is then sent to the host.
Example:
START 109 * 1 #
Changes Invalid Code Reporting To ON
Default:
Invalid Code Reporting OFF
Related CMDs:
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Reporting and Printing Setups
CMD 05 – Reporting Modes
CMD 06 – Disable printing of grants on selected doors
CMD 105, 106 – Disable Device or Disable Reports During Time Zone
CMD 107, 90*2/97*1 – Daily Report Printing On/Off
CMD 110: CHANGE ENTRY / EXIT DELAY FOR LINE MODULE INPUT
Syntax:
START 110 * N * Delay Time (0-255 secs) * Line Module Input #
Variables:
N
1 Entry Delay
2 Exit Delay
Description:
Entry and exit alarm delays are required when security system designs call for the alarm control ScramblePad/MATCH Reader to be placed inside the secure area. The entry/exit delay range is 0 - 255 seconds.
When an entry delay is used, an authorized person enters the secured area which causes an alarm condition on the line module input monitoring the entrance door or area. The alarm is not reported if the authorized individual proceeds to the interior ScramblePad/MATCH reader and enters a cancel entry delay code. If the cancel entry delay code is not entered in time, the alarm will be reported. An entry delay warning report is sent to the system printer whenever an input with an entry delay time goes into alarm. An audible entry or exit delay tone can be sounded on the ScramblePad if required by using a master control zone.
This command enables the setting of the entry delay timer. To re-secure the same facility, an exit timer code is required to enable the authorized user to leave the facility without causing an alarm. An Exit Delay Warning report is sent to the system printer whenever an exit delay code is used.
To disable the use of an Entry or Exit Delay Timer set the delay time to 0 (zero).
Example:
START 110 * 1 * 45 * 1 #
Change the Entry Delay Timer To 45 Seconds on Line Module Input 1
Default:
Entry delay = 0 seconds (delay disabled)
Exit delay = 0 seconds (delay disabled)
Related CMDs:
📄 CMD 88*8 – Print Alarm Setups and Status
📄 CMD 88*9 – Print Alarm Special Setups and Status
📄 CMD 188*12 – Print Setup Changes for Alarm & Sense Inputs
Adding Users
CMD 42 – Add Keypad Alarm Control User
Control Zone Setups
CMD 45 – Define Standard Control Zone
CMD 304 – Define Master Control Zone
Alarm Setups
CMD 111 – Change Entry/Exit Delays For Expansion Line Module Input
CMD 112 – Disable Entry Delay for Line Module Input during Time Zone
CMD 113 – Disable Entry Delay for Expansion Line Module Input during Time Zone
CMD 111: CHANGE ENTRY/EXIT DELAY FOR EXPANSION LINE MODULE INPUT
Syntax:
START 111 * N * Delay Time (0-255 secs) * Expansion Line Module Input #
Variables:
N
1 Entry Delay
2 Exit Delay
Description:
Entry and exit alarm delays are required when security system designs call for the alarm control ScramblePad/MATCH reader to be placed inside the secure area. The entry/exit delay range is 0 - 255 seconds.
When an entry delay is used an authorized person enters the secured area which causes an alarm condition on the line module input monitoring the entrance door or area. The alarm is not reported if the authorized individual proceeds to the interior ScramblePad/MATCH reader and enters an cancel entry delay code. If the cancel entry delay code is not entered in time, the alarm will be reported. An entry delay warning report is sent to the system printer whenever an input with an entry delay time goes into alarm. An audible entry or exit delay tone can be sounded on the ScramblePad if required by using a master control zone.
This command enables the setting of the entry delay timer. To re-secure the same facility an exit timer code is required to enable the authorized user to leave the facility without causing an alarm. An exit delay warning report is sent to the system printer whenever an exit delay code is used.
To disable the use of an entry or exit delay timer, set the delay time to 0 (zero).
Example:
START 111 * 1 * 45 * 8 #
Change the Entry Delay Timer To 45 Seconds on Expansion Line Module Input 8
Default:
Entry Delay = 0 seconds (delay disabled)
Exit Delay = 0 seconds (delay disabled)
Related CMDs:
📄 CMD 88*9 – Print Alarm Special Setups and Status
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Adding Users
CMD 42 – Add Keypad Alarm Control User
Control Zone Setups
CMD 45 – Define Standard Control Zone
CMD 301 – Add Expansion Line Module Input or Relay to Standard Control Zone
Alarm Setups
CMD 110 – Change Entry/Exit Delays For Line Module Input
CMD 112 – Disable Entry Delay for Line Module Input during Time Zone
CMD 113 – Disable Entry Delay for Expansion Line Module Input during Time Zone
CMD 112: DISABLE ENTRY DELAY FOR LINE MODULE INPUT DURING TIME ZONE
Syntax:
START 112 * Time Zone * Line Module Input #
Description:
Entry delays may be disabled during specified times of selected days by time zone on an input-by-input basis. This allows a secure facility to operate with tighter security, requiring access codes, or lock and key entry, plus cancel entry delay codes, during night time hours and normal access security, requiring only access codes, during day time hours.
Example:
START 112 * 1 * 1 #
Disable Entry Delay during Time Zone 1 For Line Module Input 1
Default:
Entry delays are not disabled by Time Zone
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*8 – Print Alarm Setups and Status
📄 CMD 88*9 – Print Alarm Special Setups and Status
📄 CMD 188*12 – Print Setup Changes for Alarm & Sense Inputs
CMD 110 – Change Entry/Exit Delays For Line Module Input
CMD 113 – Disable Entry Delay for Expansion Line Module Input during Time Zone
Time Zone Setups
CMD 52, 54, 56, 454 – Define/Clear Standard, Master Time Zones
CMD 113: DISABLE ENTRY DELAY FOR EXPANSION LINE MODULE INPUT DURING TIME ZONE
Syntax:
START 113 * Time Zone * Expansion Line Module Input #
Description:
Entry delays may be disabled during specified times of selected days by time zone on an input-by-input basis. This allows a secure facility to operate with tighter security, requiring access codes, or lock and key entry, plus cancel entry delay codes, during night time hours and normal access security, requiring only access codes, during day time hours.
Example:
START 113 * 1 * 8 #
Disable Entry Delay during Time Zone 1 For Expansion Line Module Input 8
Default:
Entry delays are not disabled by Time Zone
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 111 – Change Entry/Exit Delays For Expansion Line Module Input
CMD 112 – Disable Entry Delay for Line Module Input during Time Zone
Time Zone Setups
CMD 52, 54, 56, 454 – Define/Clear Standard, Master Time Zones
CMD 117: DEFINE STANDARD ACCESS ZONE (1-64) – 1 TIME ZONE, SPECIFIED DOORS ONLY
Syntax:
START 117 * Standard Access Zone * Time Zone * Doors # (Other versions)
START 117 * Standard Access Zone * Time Zone * Doors * Doors # (v6.7 only)
Variables:
Doors
Doors/Readers. Associates specified Doors (and corresponding entry/exit Readers) where 125 means Doors 1, 2, and 5 which assumes the association of corresponding readers 1, 2, 5, 9, 10, and 13.
In Version 6.7, Access Zones may be arranged individually by reader, using the second Doors option to specify a different set corresponding to readers 9-16.
Description:
This command is used to define a Standard Access Zone by specifying one time zone for a specified group of doors. This allows a time zone to be set or changed for one or more doors of an access zone without affecting the other doors of the same zone.
Unlike this command, CMD 24 requires a time zone to be specified for each and every door of the specified access zone. Also, CMD 24 does not allow partial changes to the time zone specification of an Access Zone. CMD 117 allows the time zone of a single door to be changed without specifying a time zone for any other door. CMD 17 forces the time zone to be the same for all doors of the specified Access Zone. CMD 117 does not force the Time Zone for all doors, but allows individual settings one door at a time.
Example:
START 117 * 4 * 1 * 2 #
Sets Time Zone For Door 2 (Readers 2 and 10) only to Time Zone 1 in Access Zone 4
START 117 * 5 * 2 * 24 * 12 #
Sets Time Zone For Readers 2, 4, 9, 10 only to Time Zone 2 in Access Zone 5
Default:
None
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*5 – Print Standard Access Zone Setups
📄 CMD 188*5 – Print Setup Changes for Standard Access Zones
Access Zone Setups
CMD 17 – Define Standard Access Zone (1-64), 1 Time Zone, Selected Doors
CMD 24 – Define Standard Access Zone (1-64), 1 Time Zone Per Door
CMD 124 – Define Standard Access Zone, 1 Time Zone Per Reader
CMD 204 – Define Master Access Zone (66-127)
CMD 249, 349 – Tag/Alert Access Zone
Time Zone Setups
CMD 52, 54, 56, 454 – Define/Clear Standard, Master Time Zones
CMD 124: DEFINE STANDARD ACCESS ZONE, 1 TIME ZONE PER READER
Syntax:
START 124 * Access Zone * NN * TZ For Reader 1/9 *
TZ For Reader 2/10 *TZ For Reader 3/11 *TZ For Reader 4/12 *TZ For Reader 5/13 *TZ For Reader 6/14 *TZ For Reader 7/15 *TZ For Reader 8/16 #
Variables:
NN
1 Readers 1-8
2 Readers 9-16
Description:
This command enables you to define standard access zones, using one time zone per reader. Each reader must be assigned a time zone.
Using one time zone per reader expands the capability of access zones by restricting access by time zone on a reader by reader basis. Each reader in a standard access zone can be restricted by any of the available time zones. Entering Time Zone 0 for a reader restricts all access at that reader.
CMD 24 defines Readers 1-8 and Readers 9-16 to use the same set of eight time zones. CMD 124 enables you to set Readers 1-8 separately from Readers 9-16. Possible applications include entry/exit readers where the exit readers must be configured to allow exit at any time.
Each reader must have a time zone value entered during programming. When a reader is not authorized in an access zone, enter Time Zone 0 in that reader field.
CMD 117 allows one or more time zones to be changed for a specified reader without affecting the time zone setting of any other reader(s).
Refer to CMD 17 for a convenient method to add standard access zones with one time zone for all doors.
Example:
START 124 * 10 * 1 * 40 * 0 * 1 * 5 * 0 * 0 * 0 * 0 #
START 124 * 10 * 2 * 65 * 65 * 65 * 65 * 65 * 65 * 65 * 65 #
Assign Standard Access Zone 10 To Time Zone 40 on Reader 1, TZ 0 on Reader 2 5 6 7 &
8, TZ 1 on Reader 3, TZ 5 on Reader 4, and TZ 65 on Readers 9-16.
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 - Print Standard, Master, Grand Master Time Zones
📄 CMD 88*5 - Print Standard Access Zone Setups
📄 CMD 188*5 - Print Setup Changes for Standard Access Zones
Access Zone Setups
CMD 17 – Define Standard Access Zone (1-64), 1 Time Zone, Selected Doors
CMD 24 – Define Standard Access Zone (1-64), 1 Time Zone Per Door
CMD 117 - Define Standard Access Zone (1-64), 1 Time Zone Per Door, Specified Doors
CMD 204 – Define Master Access Zone (66-127)
CMD 249, 349 – Tag/Alert Access Zone
Time Zone Setups
CMD 52, 54, 56, 154, 454 – Define/Clear Standard, Master Time Zones
Holiday Setups
CMD 57 – Define Holiday
CMD 140: SET REPORT BUFFER ALARM THRESHOLD
Syntax:
START 140 * Report Buffer Alarm Threshold #
Description:
This Command is part of the Remote Site Management feature set. It establishes the quantity of alarm events in either the standard on-board alarm buffer or the optional expanded alarm buffer that will cause the controller at the remote site to dial the Host PC.
The standard on-board buffer can hold up to 100 alarm events so its threshold setting can be from 1 event to 100 events. The expanded buffer can hold up to 22,300 events so its setting can be from 1 event to 22,300 events.
Example:
START 140 * 50 #
Dial Host When 50 Alarm Events Are In the Standard Buffer
START 140 * 1000 #
Dial Host When 1,000 Alarm Events Are In the Expanded Buffer
Default:
Report Buffer Threshold = None
Related CMDs:
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Alarm Setups
CMD 261 – Define Alarm Actions
CMD 146 – Disable Passback and Occupancy Control During Time Zone
CMD 146: DISABLE PASSBACK AND OCCUPANCY CONTROL DURING TIME ZONE
Syntax:
START 146 * Time Zone #
Description:
This command enables passback controls to be disabled during a specified time zone. This is often used to disable passback controls during shift changes, lunch periods, or other times of high traffic to reduce the number of inadvertent passback violations. The controller automatically issues a forgive all users just prior to re-enabling passback. This command also disables occupancy counting and controls during the specified time zone.
This means that if the controller has been programmed to respond in an automatic mode to occupancy counts, such as mask or unmask an area, or go from 2-person access rule to 1- person access rule, then these features will not be operational during the specified time zone. The controller automatically issues a forgive all users just prior to re-enabling occupancy controls which means it sets the inside user count for the controlled area to zero.
Example:
START 146 * 1 #
Disable Passback And Occupancy Controls During Time Zone 1
Default:
Passback Disabled During Time Zone 0 (Never)
Related CMDs:
📄 CMD 88*2 – Print System Information
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*11 – Print Keypad/Match Setups and Status
📄 CMD 188*9 – Print Setup Changes for Passback & User Management
Passback Functions
CMD 03*7, 03*8, 03*9, 03*10 – Change Reader Functions (Passback)
CMD 46 – Change Passback Mode
Time Zone Setups
CMD 52, 54, 56 – Define/Clear Standard, Master Time Zones
CMD 149: ALERT USER OR RANGE OF USERS
Syntax:
START 149 * NN * Starting User Number * Ending User Number #
Variables:
NN
0 Alert NO
1 Alert YES
Description:
Alert a user is utilized to notify a user that a special condition exists such as: a message is waiting, a new code is to be issued, a briefing is scheduled, a meeting is required, etc.
The alert is sounded as 4 short beeps of the ScramblePad Keypad's alarm annunciator when the user enters their valid code at any ScramblePad Keypad in the system. Alert does not work on a MATCH reader unless it is at a dual technology reader which includes a ScramblePad. The alert for the specified user is active until it has been turned off.
The alert message does not trigger any relays.
Example:
START 149 * 1 * 100 * 100 #
Alerts User 100
Default:
No users are alerted
Related CMDs:
📄 CMD 30, 31, 33, 34 – Print User, Users, Users by Zone, or Family of Users Without Codes
📄 CMD 35, 36, 38, 330*11 – Print User, Users, or Family of Users with Codes
Tag and Alert Setups
CMD 49 – Tag any User or Range of Users
CMD 249, 349 – Tag/Alert Access Zone
CMD 449, 549 – Tag/Alert Control Zone
CMD 154: DEFINE GRAND MASTER TIME ZONE (130-149)
Syntax:
START 154 * STZ/MTZ * Grand Master Time Zone * Column #
Description:
A Grand Master Time Zone (GTZ) is used for special time management control applications when multiple time zones are required to manage access, alarms or relays with frequent and complex time changes. A grand master time zone consists of up to 8 standard (STZ) or master time zones (MTZ).
The printed Grand Master Time Zone Report appears as follows:
| Time Zones - Column |
| |||||||
GTZ | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
130 | 0 | 0 | 0 | 0 | 0 | 0 | 66 | 0 | Inactive |
131 | 67 | 0 | 68 | 94 | 0 | 0 | 0 | 0 | Active |
Notice that GTZ 130 has 7 time zones set to 0 (zero), never, and 1 set to MTZ 66, and its current status is inactive.
GTZ 131 has several time zones programmed in columns 1, 3 and 4. One of these time zones contains a time zone which has a start time and end time that includes the current time so that zone is active.
Example:
START 154 * 66 * 130 * 7 #
Add Master Time Zone 66 To Column 7 of Grand Master Time Zone 130
Default:
None
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 188*10 – Print Setup Changes for Time Zones
Time Zone Setups
CMD 52, 54, 56, 454 – Define/Clear Standard, Master Time Zones
CMD 170: ENABLE EXPANSION LINE MODULE INPUT
Syntax:
START 170 * Expansion Input # (v6.6 or earlier)
START 170 * Expansion Input [* Exp. Input...* Exp. Input] # (v7)
Description:
Expansion line module inputs are factory set to be enabled to sense the alarm devices attached to the required DTLM or MELM on start-up. Unused inputs should be disabled with Command 171.
When an expansion line module input is set to report as an alarm, as it is on factory setup, it will report the following conditions:
â—¾ Secure
â—¾ Alarm
â—¾ Mask Request Granted
â—¾ Open
â—¾ Short
â—¾ Excessive Noise
â—¾ Line Out Of Spec
â—¾ Tamper (DTLM3/MELM3 Only)
When the line module input is set to report as a door with CMD 186, the alarm will report as a Door Forced Open and as Door Open Too Long. All other reporting remains the same.
When a Request To Exit (RQE) push button or sensor is activated it will mask the line module input for the door mode time. When a line module input is masked by a time zone or by an alarm masking code, or is masked when a relay is actuated by an access code, unlock code, time zone or control code, only the door forced or line module input report is masked. All other reporting remains active.
When an Input is disabled, all reporting is off and the associated RQE will not work.
Using v7.0, you can enable or disable up to 8 expansion inputs all at once as shown in the extended arguments. v7.0 also supports a new alarm expansion board type, AEB, that enables you to install up to four input expansion boards—and up to 32 expansion inputs— into one controller.
Example:
START 170 * 1 #
Enable Expansion Line Module Input 1 To Report Alarms
START 170 * 2 * 3 * 4 * 15 * 16 #
For V7.0, this enables Expansion Alarm Input 2, 3, 4, 15, and 16 to Report Alarms.
Default:
Enabled
Related CMDs:
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 70-72 – Enable, Disable, Change Selected Line Module Input
CMD 171 – Disable Expansion Line Module Input
CMD 172 – Change Expansion Line Module Input
CMD 173 – Change Expansion RQE (Request To Exit)
CMD 174 – Change Expansion Door Open Too Long Time
CMD 175 – Expansion DOTL Active While Input Unlocked
CMD 176 – Mask Expansion Line Module Input during Time Zone
CMD 180 – Change Door Time for Expansion Line Module Input
CMD 171: DISABLE EXPANSION LINE MODULE INPUT
Syntax:
START 171 * Expansion Input # (v6.6 or earlier)
START 171 * Expansion Input [* Exp. Input... * Exp. Input] # (v7)
Description:
Expansion line module inputs are factory set to be enabled to sense the alarm devices attached to the required DTLM or MELM on start up. Unused Inputs should be disabled with this command.
With v7.0, you can enable or disable up to 8 expansion inputs at once using the extended arguments.
When disabled, all reporting is off.
When an Input is disabled, all reporting is off and the associated RQE will not work.
Example:
START 171 * 1 #
Disable All Alarm Reporting From Expansion Line Module Input 1
START 171 * 2 * 3 * 4 * 15 * 16 #
For v7.0 and above, disables all alarm reporting from Expansion Alarm Input 2, 3, 4, 15, and 16.
Default:
Enabled
Related CMDs:
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 170 – Enable Expansion Line Module Input
CMD 172: CHANGE EXPANSION LINE MODULE INPUT
Syntax:
START 172 * NN * Expansion Input #
Variables:
NN
1 Normally Open (When Secure)
2 Normally Closed (When Secure)
Description:
Alarm sensor inputs are usually Normally Closed switches when secure and open on alarm. They may be set to Normally Open for sensors whose contacts are normally open when secure.
Example:
START 172 * 1 * 1 #
Change Expansion Line Module Input 1 To Normally Open When Secure
Default:
Normally Closed
Related CMDs:
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 173 – Change Expansion RQE (Request To Exit)
CMD 174 – Change Expansion Door Open Too Long Time
CMD 175 – Expansion DOTL Active While Input Unlocked
CMD 176 – Mask Expansion Line Module Input during Time Zone
CMD 173: CHANGE EXPANSION RQE
Syntax:
START 173 * N * Expansion Input #
Variables:
N
1 RQE Re-Triggers Mask While Activated
2 RQE Triggers Mask Once When Activated
3 RQE OFF
Description:
Each RQE input is factory set to OFF.
The RQE will trigger the masking of the input once unless it is set to continuously trigger for as long as it is activated.
An expansion RQE cannot trigger an expansion relay.
Expansion line module inputs set to operate/report as a door can be used to monitor auxiliary doors such as emergency fire exits. These doors may be authorized employee exits but not entrances. The RQE input would be used to mask the door forced alarm upon authorized exit. Door Open Too Long alarm reporting also operates on expansion line module inputs reporting as doors.
Expansion line module inputs are set to report as zone alarms from the factory. In this case the RQE reports as Mask Request Granted. This enables local masking from high security key switches or other normally open switch devices.
A DTLM2/3 or MELM2/3 is required.
Example:
START 173 * 1 * 1 #
Change RQE on the expansion input 1 to re-trigger masking
Default:
RQE OFF
Related CMDs:
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 88*22 – Print Expansion Line Module Input Door Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 172 – Change Expansion Line Module Input
CMD 174 – Change Expansion Door Open Too Long Time
CMD 175 – Expansion DOTL Active While Input Unlocked
CMD 176 – Mask Expansion Line Module Input during Time Zone
CMD 174: CHANGE EXPANSION DOOR OPEN TOO LONG TIME
Syntax:
START 174 * DOTL Time * Expansion Input #
Description:
Any expansion line module input may be set up to report as a door. The unauthorized opening of a door is reported as a Door Forced Open. The door is also monitored for being held Open-Too-Long beyond an adjustable time delay of 0-8100 (0=Off) seconds. Both door alarm conditions report on the printer and trigger the alarm relay.
The Door-Open-Too-Long timer starts at the end of the door mode timer. For example, if the door unlock timer is set to 6 seconds and the door is held open, the DOTL timer starts after the 6 second door unlock time expires. If the DOTL Timer is set to 10 seconds the alarm will sound after 16 seconds total time has expired.
A DTLM/MELM is required.
Example:
START 174 * 15 * 1 #
Define Door-Open-Too-Long Alarm Delay To 15 Seconds For Expansion Input 1
Default:
12 seconds
Related CMDs:
📄 CMD 88*10 – Print Door Setups and Status
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 88*22 – Print Expansion Line Module Input Door Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 172 – Change Expansion Line Module Input
CMD 173 – Change Expansion RQE (Request To Exit)
CMD 175 – Expansion DOTL Active While Input Unlocked
CMD 176 – Mask Expansion Line Module Input during Time Zone
CMD 282 – Define Special Needs Unlock Extension Time
CMD 175: EXPANSION DOTL ACTIVE WHILE INPUT UNLOCKED
Syntax:
START 175 * N * Expansion Input #
Variables:
N
0 NO
1 YES
2 NO (for v6.5 and earlier)
Description:
Any expansion line module input can be set up to report as a door. The door held open alarm will not report on an expansion input masked by time zone or code. It may be made to report on a masked input by making DOTL active when the input unlocked by an unlock code, momentary mask code, or RQE retriggers.
If the input associated with the door is masked by a code or time zone, then a DOTL alarm will not report even if the DOTL is active while the door is unlocked.
A DTLM/MELM is required.
Example:
START 175 * 1 * 1 #
Sets DOTL Alarm Reporting Always On Even When Expansion Input 1 Is Legally Unlocked By an Unlock Code Or By A Momentary Mask Code. Protects Fire Doors From Being Propped Open When “Unlocked”.
Default:
No
Related CMDs:
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 88*22 – Print Expansion Line Module Input Door Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 172 – Change Expansion Line Module Input
CMD 173 – Change Expansion RQE (Request To Exit)
CMD 174 – Change Expansion Door Open Too Long Time
CMD 176 – Mask Expansion Line Module Input during Time Zone
CMD 176: MASK EXPANSION LINE MODULE INPUT DURING TIME ZONE
Syntax:
START 176 * Time Zone * Expansion Line Module Input #
Description:
Expansion line module inputs may be automatically masked during specific times of the day to disable alarm reporting. Line trouble reporting is not disabled during alarm masking. Masking is removed by setting an input’s masking time zone to 0 (zero).
A DTLM/MELM is required.
Example:
START 176 * 1 * 1 #
Masks Alarm Reporting On Expansion Line Module Input 1 During Time Zone 1
Default:
Time Zone 0 (No Automatic Masking)
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Time Zone Setups
CMD 52, 54, 56, 154 – Define/Clear Standard, Master, Grand Master Time Zones
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 172 – Change Expansion Line Module Input
CMD 173 – Change Expansion RQE (Request To Exit)
CMD 174 – Change Expansion Door Open Too Long Time
CMD 175 – Expansion DOTL Active While Input Unlocked
CMD 180: CHANGE DOOR TIME FOR EXPANSION LINE MODULE INPUT
Syntax:
START 180 * Door Timer * Expansion Line Module Input #
Description:
The expansion line module inputs masking time is set up with the door timer.
Any expansion line module input may be set to operate and report as a door or as an alarm. Each input may be assigned to an access zone or to a control zone, or to both, depending on how the input is to be controlled.
When assigned to an access zone for one-ScramblePad/MATCH Reader-to-one-input type control, the access code used to mask an input uses the door timer as the masking timer. When assigned to a control zone for any-ScramblePad/MATCH Reader-to-any-input type control, the control code used to mask the input also uses the door timer as the masking timer.
The door time is momentary with an adjustable time of 0-8100 seconds (0=Toggle). An expansion line module input's door timer is used by access codes and the RQE input.
For more information on expansion input control time, see CMD 181.
Example:
START 180 * 10 * 1 #
Change Door Time To 10 Seconds For Expansion Line Module Input 1
Default:
6 seconds
Related CMDs:
📄 CMD 88*18 – Print Expansion Relay Setups and Status
📄 CMD 88*22 – Print Expansion Line Module Input Door Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Adding Users
CMD 10, 19-22, 310-315, 320-322 – Add Access Users
CMD 15, 40, 41, 44 – Add Control Users
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
Relay Setups
CMD 181 – Change Control Time for Expansion Relay
CMD 181: CHANGE CONTROL TIME FOR EXPANSION RELAY
Syntax:
START 181 * Control Time * Expansion Relay #
Description:
The control time determines how long an expansion relay will be actuated by a control code or by an alarm or relay triggered control zone. The control time may be momentary with an adjustable time of 1-8100 seconds. It can toggle ON and OFF on consecutive trigger code entries if the timer is set to 0 (zero) seconds.
A relay's control time is used by control codes as well as by a line module input or relay to trigger a control zone.
For more information on the door timer for expansion inputs, see Command 180.
Example:
START 181 * 10 * 1 #
Change Control Time To 10 Seconds For Expansion Relay 1
Default:
6 seconds
Related CMDs:
📄 CMD 88*18 – Print Expansion Relay Setups and Status
📄 CMD 88*28 – Print Virtual Relay Setups and Status
📄 CMD 188*15 – Print Setup Changes for Expansion Relays
Adding Users
CMD 10, 19-22, 310-315, 320-322 – Add Access Users
CMD 15, 40, 41, 44 – Add Control Users
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 180 – Change Door Time for Expansion Line Module Input
Relay Setups
CMD 181 – Change Control Time of Relay
CMD 182: TIME ZONE CONTROL OF EXPANSION RELAY
Syntax:
START 182 * N * Expansion Relay * Time Zone #
Variables:
N
1 Actuate Relay During Time Zone
2 Disable Relay During Time Zone
3 Clear Relay At End Of Time Zone
Description:
Expansion relays may be actuated during a time zone, going on at the start time of the zone and off at the end time of the zone.
Expansion relays may be disabled during a time zone, becoming disabled at the start of the zone and reenabled at the end of the zone.
The current state of any relay may be auto-cleared at the end of a time zone to insure the automatic reset of a lower priority code activated event without the need for a manual resetting of the event.
Example:
START 182 * 1 * 1 * 1 #
Auto-Actuate Expansion Relay 1 During Time Zone 1
START 182 * 2 * 1 * 5 #
Auto-Disable Expansion Relay 1 During Time Zone 5
START 182 * 3 * 6 * 1 #
Auto-Clear Expansion Relay 6 At The End Of Time Zone 1
Default:
Actuate Relay during Time Zone 0 (Never)
Disable Relay during Time Zone 0 (Never)
Clear Relay at the end of Time Zone 0 (Never)
Related CMDs:
📄 CMD 88*3, 88*4, 88*14 – Print Standard, Master, Grand Master Time Zones
📄 CMD 88*18 – Print Expansion Relay Setups and Status
📄 CMD 88*19 – Print Detailed Expansion Relay Status Only
📄 CMD 88*28 – Print Virtual Relay Setups and Status
📄 CMD 188*15 – Print Setup Changes for Expansion Relays
Adding Control Users
CMD 15 – Add Keypad Unlock/Relock User (IDF 1)
CMD 40 – Add Keypad Relay Control User
CMD 41 – Add Keypad Top-Priority Relay Control User (IDF 1)
Time Zone Setups
CMD 52, 54, 56, 154 – Define/Clear Standard, Master, Grand Master Time Zones
Alarm Setups
CMD 180 – Change Door Time for Expansion Line Module Input
CMD 183 – Clear Time Zone Control of Expansion Relay
CMD 183: CLEAR TIME ZONE CONTROL OF EXPANSION RELAY
Syntax:
START 183 * Expansion Relay #
Description:
Time zone control of any expansion relay can be cleared and reset to none.
Use CMD 88*18 to print the current status of expansion relays. This is the best method to determine why a relay is performing in a certain way on a code entry or other event.
Example:
START 183 * 1 #
Clear Time Zone Control Of Expansion Relay 1 To None
Default:
None
Related CMDs:
📄 CMD 88*18 – Print Expansion Relay Setups and Status
📄 CMD 188*15 – Print Setup Changes for Expansion Relays
Time Zone Setups
CMD 52, 54, 56, 154, 454 – Define/Clear Standard, Master, Grand Master Time Zones
Alarm Setups
CMD 180 – Change Door Time for Expansion Line Module Input
Relay Setups
CMD 182 – Time Zone Control of Expansion Relay
CMD 184: EXPANSION LINE MODULE INPUT TRIGGERS CONTROL ZONE
Syntax:
START 184 * N * Expansion Line Module Input * Control Zone #
Variables:
N
1 Triggers
2 Re-Triggers
3 Actuate
4 Disable
Description:
Any expansion line module input can trigger any control zone. To cancel an alarm trigger of a control zone set the specified input to trigger control zone 0 (none). To trigger a control zone means to start the zone's relay control timers at the moment the alarm occurs.
The relay timers will start and time out even if the alarm stays active. To retrigger means that the relay timers are not started until the alarm event restores. To actuate a control zone means to actuate its relays for as long as the alarm is active and release them the moment the alarm restores.
The relay timers are ignored when ‘actuate’ is used. To disable means the relays are disabled while the alarm is active. Once it restores the disabled state is cleared. If the relays have control delays programmed, they will be recognized by the trigger and retrigger controls but not by the actuate and disable controls.
This feature allows special control capabilities such as turning on perimeter lights when an alarm is triggered, or for annunciation of a specific line module input, or control of HVAC and lighting systems. When using a master control zone in this command, master control zones can only be triggered, not retriggered, actuated, or disabled.
Example:
START 184 * 1 * 1 * 1 #
Line Module Input 1 Triggers Control Zone 1
Default:
None
Related CMDs:
📄 CMD 88*6 – Print Standard Control Zone Setups
📄 CMD 88*16 – Print Master Control Zone Setups
📄 CMD 88*17 – Print Detailed Relay Status Only
📄 CMD 88*19 – Print Detailed Expansion Relay Status Only
📄 CMD 88*20 – Print Expansion Alarm/RQE Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Relay Setups
CMD 81 – Change Control Time of Relay
Alarm Setups
CMD 84 – Line Module Input Triggers Control Zone
CMD 185: CHANGE FUNCTION OF EXPANSION RELAY
Syntax:
START 185 * N * Expansion Relay #
Variables:
N
0 Relay Rests OFF
1 Relay Rests ON
2 Relay Rests OFF (for v6.5 and earlier)
Description:
The operation and outputs of each relay may be inverted. On system start up they rest in the de-energized, or OFF state and the outputs are as marked on the circuit board. Each relay may be changed to rest in the energized or ON state which inverts the meaning of the outputs: the normally opened contact becomes the normally closed contact.
For example, when controlling elevators, always change the relays to resting ON. This ensures that if the control system power fails, the relay coil will be de-energized, falling to the OFF condition, thereby allowing the elevator to be used.
Example:
START 185 * 1 * 1 #
Change Expansion Relay 1 To Rest ON For Elevator Control
Default:
Relay Rests OFF
Related CMDs:
📄 CMD 88*17 – Print Detailed Relay Status Only
📄 CMD 88*18 – Print Expansion Relay Setups and Status
📄 CMD 88*19 – Print Detailed Expansion Relay Status Only
📄 CMD 88*28 – Print Virtual Relay Setups and Status
📄 CMD 188*15 – Print Setup Changes for Expansion Relays
Relay Setups
CMD 81 – Change Control Time of Relay
CMD 85 – Change Operation for Selected Relays
CMD 186: CHANGE EXPANSION LINE MODULE INPUT REPORTING MODE
Syntax:
START 186 * N * Expansion Line Module Input #
Variables:
N
1 Report As A Door
2 Report As An Alarm
Description:
Any expansion line module input may be set up to report as a door or as an alarm zone. Each input may be assigned to an access zone, control zone, or both, depending on how the input is to be controlled.
When set to report as a door, the input will report Door Forced Open and Door Open Too Long alarms. This can provide monitoring and reporting of secure emergency exit doors. If these doors are to be used for authorized exit, they should be equipped with RQE push button or motion sensors to mask the Door Forced Alarm condition. If they are held open too long, a DOTL alarm will occur.
Each of these doors can be equipped with a ScramblePad and controlled with an access code. This enables access by alarm on these doors. Opening them without a code will cause a Door Forced Alarm. They can also be controlled from a central ScramblePad after an intercom request from the door location. An access request to a central office would enable an operator to enter a code to momentarily mask the specific door authorized for use.
When set up as an alarm zone, the input will report alarm and alarm active too long conditions. The alarm report occurs when the input is first tripped. An AATL alarm functions like a DOTL alarm on a door. If a code has been entered to mask a line module input momentarily but the sensor stays tripped after the momentary mask time expires, an AATL will be reported.
Example:
START 186 * 1 * 1 #
Expansion Line Module Input 1 Reports As A Door
Default:
Report as an Alarm
Related CMDs:
📄 CMD 88*21 – Print Expansion Alarm Special Setups and Status
📄 CMD 88*22 – Print Expansion Line Module Input Door Setups and Status
📄 CMD 188*13 – Print Setup Changes for Expansion Line Module Inputs
Alarm Setups
CMD 170, 171 – Enable, Disable Expansion Line Module Input
CMD 174 – Change Expansion Door Open Too Long Time
CMD 175 – Expansion DOTL Active While Input Unlocked
CMD 187: EXPANSION RELAY TRIGGERS CONTROL ZONE
Syntax:
START 187 * N * Expansion Relay * Control Zone #
Variables:
N
1 Triggers
2 Retriggers
Description:
Any expansion relay can trigger any control zone. To cancel a relay trigger of a control zone set the specified input to trigger Control Zone 0 (none). To trigger a control zone means to start the zone's relay control timers at the moment the expansion relay changes state. The relay timers will start and time out even if the relay stays actuated. To retrigger means that the relay timers are not started until the relay reverts back to its resting state.
This feature allows special control capabilities such as shunting other alarm panels when a relay is triggered, or for annunciation of a specific relay output, or control HVAC and lighting systems. When using a master control zone in this command note that master control zones can only be triggered, not retriggered, actuated, or disabled.
Example:
START 187 * 1 * 2 * 6 #
Expansion Relay 2 Triggers Control Zone 6
Default:
None
Related CMDs:
📄 CMD 88*16 – Print Master Control Zone Setups
📄 CMD 88*17 – Print Detailed Relay Status Only
📄 CMD 88*18 – Print Expansion Relay Setups and Status
📄 CMD 88*19 – Print Detailed Expansion Relay Status Only
📄 CMD 88*28 – Print Virtual Relay Setups and Status
📄 CMD 188*15 – Print Setup Changes for Expansion Relays
Control Zone Setups
CMD 45 – Define Standard Control Zone
CMD 84 –Line Module Input Triggers Control Zone
CMD 184 – Expansion Line Module Input Triggers Control Zone
Relay Setups
CMD 181 – Change Control Time for Expansion Relay
CMD 188: PRINT COMMAND SETUPS
Syntax:
START 188 * NN * [NN...] #
Variables:
NN
0 | System Setups Command Report |
|
1 | Clock Setups | CMD 50 - 51 |
2 | Holiday Table Setups | CMD 57 - 59 |
3 | Keypad Setups | CMD 3, 103 - 104 |
4 | Reporting Mode Setups | CMD 05-09, 18, 105-109, 140, 191-195 |
5 | Standard Access Zone Setups | CMD 17, 24, 117, 201, 203, 217, 249, 349 |
6 | Master Access Zone Setups | CMD 204, 217, 249, 349 |
7 | Standard Control Zone Setups | CMD 45, 301-303, 345 |
8 | Master Control Zone Setups | CMD 304-307 |
9 | Passback & User Management Setups | CMD 46, 146, 235-238, 255-257 |
10 | Standard Time Zone Setups | CMD 52, 54, 56, 154 |
11 | Alarm Action Control Blocks Setups | CMD 261 |
12 | Alarm & Sense Input Setups | CMD 70-77, 84, 110, 112, 270 |
13 | Expansion Line Module Input Setups | CMD 111, 113, 170-176, 180, 184, 186 |
14 | Relay Setups | CMD 79-83, 85-87, 280-281 |
15 | Expansion Relay Setups | CMD 181-183, 185, 187 |
Any setup changed using one of the commands cited above will be reported by CMD 188.
Description:
Use this command to print a full or partial report list of changes made to setups since cold start. For a complete list of all setup values, refer to CMD 88.
Printing the date, time and version prints the current date, time and the controller’s CCM Version Number.
Printing the standard time zones prints a list of all standard time zones defined with their starting time, ending time and days, and their current active or inactive state. Printing the master time zones prints a list of any of the master time zones which have been assigned standard time zones and their current active or inactive state. Printing the access zones or control zones prints their time zone and door/relay setups.
Printing the relays prints the relay setup tables and the relay status display. The detailed report shows the exact current status of each relay changed since cold start.
Printing the alarm and sense inputs prints a list of alarm and sense inputs modified from default and their current state. Printing the keypads/MATCH values prints the keypads/ MATCH reader setup tables. Printing the holidays prints the holiday list.
For v6.6 and later, this command allows printout of up to ten arguments.
No sensitive information is contained in these printouts.
Example:
START 188 * 0 #
Print a list of all system components modified since cold start
START 188 * 2 #
Prints the CMD 57’s used to set up all holiday tables.
START 188 * 10 * 14 #
Prints list of all Time Zones and Relays changed since cold start
Default:
None
Related CMDs:
📄 CMD 36 – Print Users with Codes
📄 CMD 88 – Print List of All Current Values
📄 CMD 260 – Print Alarm Action(s)
CMD 191: CHANGE PAGE LENGTH FOR PRINTER
Syntax:
START 191 * LINES #
Description:
All DIGI*TRAC controllers include the capability to print in different languages. To accommodate these languages, different countries will use different paper lengths for their standard computer paper. For instance, the standard European paper size is A4. In addition, some companies use larger or smaller paper formats, like legal size or A4, in their system printers, allowing the controller to print more lines or fewer lines of text on a page.
Use this command to specify the number of lines per page you require for your system printer.
The default page length is the American standard for 8.5 x 11: 58 lines per page.
Example:
START 191 * 66 #
Print 66 Lines per page
START 191 * 0 #
Never form-feed the printer (this is the default)
Default:
0 lines per page (never form feed printer)
Related CMDs:
📄 CMD 88*23 – Print Reporting Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
CMD 192: CHANGE PROGRAMMING MODE TIMEOUT INTERVAL
Syntax:
START 192 * Time-out Time #
Description:
To program stand-alone controllers, programming mode is invoked at a ScramblePad. Normally, CMD 99 is used to quit Programming Mode manually at the end of a programming session. However, if the operator forgets to quit programming mode, the controller will automatically time out and return to normal entry mode after 8 minutes without command activity on the programming ScramblePad.
Use this command to change the time-out interval from the 8 minute default to any interval from 2 - 20 minutes.
Example:
START 192 * 15 #
Change Programming Mode Time-out to 15 minutes
Default:
8 minutes
Related CMDs:
📄 CMD 88*2 – Print System Information
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
CMD 01, 13*0 – Change System (User 0) Code
CMD 02 – Add Programming Pass/word
CMD 99 – Quit Programming
CMD 193: SET HOST PHONE NUMBER
Syntax:
START 193 * N * Phone Number #
Variables:
N
1 First Number
2 Second Number
3 Third Number
4 Fourth Number
Description:
Use this command to configure up to four host phone numbers a controller at a remote site can call. Each phone number can contain up to 16 digits.
Most networks only have a single main site phone number; however, this feature accepts up to 4 phone numbers as alternate numbers which can be called if the first number is either busy or out-of-service.
The controller at the remote site will dial the first number first. If there is only one number programmed, it will continue to dial until the call has been completed. If a second, third or fourth number has been programmed into the controller, it will automatically rotate through the numbers until the call has been successfully completed. This allows for an emergency backup host to receive calls from remote sites if the primary host at the main site is either busy or off-line.
This command is part of the Remote Site Management feature set.
Example:
START 193 * 1 * 17142509990 #
Sets Phone Number 1 to 714 250-9990
START 193 * 2 * 18005551212 #
Sets Phone Number 2 to 1 800 555-1212
Default:
None (no phone numbers are preset)
Related CMDs:
📄 CMD 88*24 – Print Remote Site Management Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Modem Setups
CMD 90*2, 97*2, 97*4, 97*8 – Host Setup Commands
CMD 108 – Time Zone Control of Modem
CMD 194 – Select Tone or Pulse Dialing
CMD 195 – Change Host Call-Back
Alarm Setups
CMD 261 – Define Alarm Actions
CMD 194: SELECT TONE OR PULSE DIALING
Syntax:
START 194 * N #
Variables:
N
1 Tone Dialing
2 Pulse Dialing
Description:
This command enables the modem at the remote site to communicate with either a Tone or Pulse Dialing phone system.
This Command is part of the Remote Site Management feature set.
Example:
START 194 * 2 #
Sets Modem to Pulse Dialing
Default:
Tone Dialing
Related CMDs:
📄 CMD 88*24 – Print Remote Site Management Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Modem Setups
CMD 90*2, 97*2, 97*4, 97*8 – Host Setup Commands
CMD 108 – Time Zone Control of Modem
CMD 193 – Set Host Phone Number(s)
CMD 195 – Change Host Call-Back
Alarm Setups
CMD 261 – Define Alarm Actions
CMD 195: CHANGE HOST CALL-BACK
Syntax:
START 195 * N #
Variables:
N
0 Disable
1 Enable
2 Disable
Description:
Use this command to force an automatic call-back from the controller(s) at the remote site to the host at the main site whenever the host initiates a call to the remote site. This insures that the call originates from the host at the main site, not from an unknown host attempting an unauthorized logon to a controller at the remote site.
This command is part of the Remote Site Management feature set.
Some networks do not allow remote site management from multiple hosts. If this operation is needed, do not enable host call-back.
On some networks the remote site is billed for phone changes related to communications between it and the main site. Enable host call-back if this mode of operation is needed.
Comment:
In v6.5, you had to turn the host call-back feature on (“dialoutonly”), then use 198*4*0*0*0*0# to trigger the actual dial-back from the panel. There could be complications: if this feature was enabled but the host didn't send CMD 198*4, nothing would hap- pen: it wouldn't let the host “log on.” With v6.6 and later, attempting to log on triggers a dial-back, exactly as if a 198*4 command were sent.
Example:
START 195 * 1 #
Enables Host Call Back
Default:
Disabled (195*2)
Related CMDs:
📄 CMD 88*24 – Print Remote Site Management Setups
📄 CMD 188*4 – Print Setup Changes for Reporting and Duress
Modem Setups
CMD 90*2, 97*2, 97*4, 97*8 – Host Setup Commands
CMD 108 – Time Zone Control of Modem
CMD 193 – Set Host Phone Number(s)
CMD 194 – Select Tone or Pulse Dialing
Alarm Setups
CMD 261 – Define Alarm Actions