Versions Compared

Old Version 4

changes.mady.by.user Del Gonzalez

Saved on

compared with

New Version Current

changes.mady.by.user Anand Rajaraman

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Table of Content Zone
Table of Contents

Bosch Intrusion Detection System

Bosch IDS plugin acts as an interface to the following models such as B4512, B5512, B6512, B8512, and B9512. It fetches panel information, executes panel/area/point/output commands, monitors events/alarms, and displays the same in Velocity.

Bosch IDS Panel System Requirements in Velocity

The following lists the required configuration:

Software

Version

Velocity

3.8.4.xxxx

Velocity IDS Framework

1.0.0.146

Velocity Bosch IDS Plugin

1.0.3.198

Licensing

Licensing Velocity Integration and Bosch IDS Plugin

Prerequisites

To obtain Bosch IDS plugin license you will need a licensed Velocity 3.8.4, and a personal computer with email access so you can provide Identiv with information about your Velocity system and receive a license key.

...

The license key is only valid on the computer with the specified Server ID; it cannot be used on a different computer.

Installation

Installing Bosch IDS Plugin

Prerequisite: To install Velocity IDS Bosch plugin, the user must be logged into Windows using an account that has local Administrator privileges, you must be a member of the Velocity Administrators Role, have an active license for the integration, know the name and password of the Velocity Services Account (specified when Velocity was installed).

...

  1. Open Velocity application. Select Event Viewer and scroll down to check IDS Service Online software event is generated.

Bosch IDS Panel

Remote Procedure Software (RPS) Configuration

To communicate with Velocity the panel must first be configured using the Bosch RPS tool to set the Automation Device and Automation password properties.

  1. In RPS Menu, navigate to Automation/Remote App -> Automation Device.

  2. In the Automation Device screen, select Mode 2 from the options to be the Data Value and click OK.

Adding a Bosch IDS Panel

The Bosch IDS panel must be configured with a valid IP Address, Port, and Automation Passcode.

...

  1. Enter the Name, Vendor, Model Type, Timezone, IP Address, Port, and Automation Passcode.

  2. Click OK.
    After the new panel is added, the Areas, Points, and Outputs are automatically displayed and populated below the panel.

Monitoring Bosch IDS Panels

The Bosch IDS panel status displays the current status of all connected panel areas, points, and outputs. The mapped IDS events and the alarms that get generated can be monitored from Event Viewer or Graphics.

Bosch IDS Panel Areas

Areas in the IDS Panel define a group of points. The IDS Areas folder displays the areas that are defined in the Bosch Panel.

...

Command

Description

Silence Bells

Allows to silence the alarm bell generated by an event

Activate Bells

Allows to activate the alarm bell generated by an event

Disarm

Allows to Disarm (OFF)

All on Instant

Turns on all points with no entry or exit delay

All on Delay

Turns on all points with entry or exit delay

Part on Instant

Turns on only some of the points with no entry or exit delay

Part on Delay

Turns on only some of the points with entry or exit delay

Force All on Delay

Forces all points to turn on with entry or exit delay

Force All on Instant

Forces all points to turn on with no entry or exit delay

Force Part on Delay

Forces only some of the points to turn on with entry or exit delay

Force Part on Instant

Forces only some of the points to turn on with no entry or exit delay

Stay One Arm

Arm in stay mode

Away Arm

Arm in away mode

Force Stay One Arm

Force arm in stay mode

Force Away Arm

Force arm in away mode

Reset Sensors

Resets the sensors in the area from a previous action and returns to normal operation

Bosch IDS Panel Points

Points refer to single points such as doors, windows, fire detection sensors, etc. A group of points comprises an area such as lobby, conference room, etc. 

...

Command

Description

Bypass Point

Bypasses the selected point

Unbypass point

Un-bypasses the selected point

Bosch IDS Panel Outputs

Outputs in IDS refers to automatic control of devices in areas such as entry/exit gates or lighting in secured zones.

...

Command

Description

Control Output ON

Turns the output relay ON

Control Output OFF

Turns the output relay OFF

Status Viewer

The Status Viewer allows you to view the status of Panels, Areas, Points, and Outputs.

Viewing IDS Panel Objects in Status Viewer

  1. Select Status Viewer from Main menu.

  2. Click Configure Status Group.

  3. Enter the Status Group name In the Status Viewer Properties window.

  4. From the Filter drop-down list, select the type of component you want to include in this status group. The 'Available' pane is populated with all devices/points corresponding to the selected Filter.

  5. Click the right arrow button, to move the highlighted components in the 'Available' pane to the 'Selected' pane.

  6. Click OK to save and return to the Status Viewer.

    1. The status viewer displays the status of the component that is added Online, through Battery status, and AC Power status.

    2. The Status Group for the corresponding Areas display as shown.

    3. The Status Group for the corresponding Points display as shown.

    4. The Status Group for the corresponding Outputs displays as shown.

...

Graphics Viewer

The Velocity Graphics module provides a visual interface for interacting with IDS Panels, Areas, Points, and outputs. Graphics supports two different kinds of IDS Objects:

...

The IDS Area construct is different and it allows you to draw an area that covers a portion of a map to visually represent the IDS Area’s physical coverage. The IDS Area construct displays the IDS Panel Area’s internal ARM and ALARM/SECURE states which are different than the Velocity alarm state (as noted above).

Difference between IDS Area VIO object and an IDS Area

To illustrate the difference between IDS Area VIO object and an IDS Area consider the following example:

An IDS area goes into alarm and a Velocity Alarm event is displayed in the Velocity Alarm Viewer and the associated IDS Area VIO object in Graphics animates to show that the VIO is in an alarm state. The operator may then acknowledge and clear the Velocity Alarm from either the IDS Area VIO or from the Velocity Alarm Viewer. However, the secure state of the IDS Area construct remains in alarm until the alarm is cleared from the IDS panel (usually from the IDS keypad).

Plotting IDS VIO Objects

Velocity Graphics requires to be in Design mode to plot VIO objects.

...

  • Delete: Removes the velocity object from the drawing area.

  • Set as Primary: Indicates the Velocity objects in the map that gets automatically enabled when set as primary. For example, if you place area 1 on three different maps, you can set area 1 as the primary.  Then, if area 1 detects an illegal entry, area 1 automatically appears on the canvas with the area 1 alarm icon displayed.

  • Configure Device…: Allows to bring up the corresponding configuration screen for that device.  For example, if you select this option for a reader, the Reader Properties screen for that reader appears.

IDS Area

The IDS Area feature allows you to visually represent an IDS Area by drawing it on a map. The IDS Area visually displays the Area’s Arm State as well as the Area’s Secure state. The border of the IDS Area represents the Arm State and the inside of the IDS Area represents the secure state. You can color code all supported Arm States to quickly visually identify how the area is armed.

Creating IDS Area

  1. Click Graphics in the Main menu.

  2. In design mode, click Design->Draw and select IDS Area.

  3. Draw the desired area on the map.

  4. The Map IDS constructs to a specific IDS panel Area and configures the IDS Area border and interior as shown

Typically the IDS VIOs gets plotted on the map as well and you will draw the IDS Area around these plotted VIO objects as shown above.

Interacting with IDS VIO Objects and IDS Area Constructs

In Graphics mode, right click anywhere on the selected IDS Area construct and execute the desired IDS Area command as shown.

...

Right click to select IDS Output and your desired command as shown.

...

Roles and Permissions

The Roles in Velocity streamline the process of assigning rights and privileges to operators by the Velocity server.

The Areas, Points, and Outputs for IDS Panels added through Velocity must be given individual access, in addition to giving overall access to IDS panels. For example, when the operator wants to access specific areas, points/outputs of a panel that is configured, the permissions for each must be given explicitly by the server.

Adding Role based Operator to access IDS Panels, Areas, Points, and Outputs

  1. Login as Velocity Superuser in Velocity Server.

  2. Navigate from Main Menu-> Administration-> Roles->Operators.

    The Role Operators window displays.

  3. Select Application Permissions->IDS Panels and enable the role for the desired functions (Add/Delete/Save/View). The operator must have view permission in order to access the IDS panel and perform any operation.

  4. Select IDS Panels or IDS Areas or IDS Points or IDS Outputs individually to give specific access.

Restricting Alarms and Events using Velocity Roles

The Velocity settings has an option to restrict alarms and events based on operator roles in Velocity. To enable this option:

  1. Right click Velocity Service Control Manager icon on Windows taskbar and select Settings.
    The Velocity Settings window displays.

  2. Go to System->Advanced in Velocity Settings.

  3. Enable Restrict alarms and events using Velocity Roles checkbox and click OK.

Limitation

Bosch IDS plugin has the following limitation

...